 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| NJG1506R SPDT SWITCH GaAs MMIC sGENERAL DESCRIPTION NJG1506R is a GaAs SPDT switch IC which features low loss, high isolation and low control current and ideally suitable for switching the RF receiving circuit of cellular phone. NJG1506R is operated in the wide frequency range from 50MHz to 3GHz at low voltage from 2.5V with a small VSP8 package. sFEATURES qSingle and low positive supply voltage qLow insertion loss qHigh isolation qTransmission Power qLow control current qPackage sPIN CONFIGURATION R TYPE (Top View) 1 sPACKAGE OUTLINE NJG1506R +2.5~+5.5V 0.3dB typ. @f=1GHz, Pin=0dBm 28dBm typ. @f=1GHz, Pin=0dBm 19dBm max. @f=2GHz, VCTR=3.0V 1uA typ. @f=0.05~2.5GHz, Pin=10dBm VSP8 (Mount Size: 4.0x2.9x1.2mm) Pin Connection 1.VCTR2 8 7 6 5 2.P2 3.GND 4.GND 5.PC 6.GND 7.P1 8.VCTR1 2 3 4 sTRUTH TABLE "H"=VCTR (H), "L"=VCTR (L) VCTR1 VCTR2 P1-PC P2-PC H L OFF ON L H ON OFF L L Loss =15dB P1 Return Loss =-3dB Loss =15dB P2 Return Loss =-3dB H H Loss =16dB P1 Return Loss =-2dB Loss =16dB P2 Return Loss =-2dB Note) The values of "Loss" and "Return Loss" are typical values at 2.0GHz. -1- NJG1506R sABSOLUTE MAXIMUM RATINGS (Ta=25C, Zs=Zl=50) PARAMETER Input power Control voltage Power dissipation Operating Temp. Storage Temp. SYMBOL Pin VCTR PD Topr Tstg RATINGS 28 6.0 320 -30~+85 -40~+150 UNITS dBm V mW C C sELECTRICAL CHARACTERISTICS (VCTR (L)=0V, VCTR (H)=2.7V, Zs=Zo=50, Ta=25C) PARAMETER Control voltage (L) Control voltage (H) Control current Insertion loss1 Insertion loss2 Isolation 1 (PC-P1, PC-P2, P1-P2) SYMBOL VCTR (L) VCTR (H) ICTR LOSS1 LOSS2 ISL1 ISL2 P-1dB VSWR TSW CONDITIONS f=0.05~2.5GHz, Pin=10dBm f=0.05~2.5GHz, Pin=10dBm f=0.05~2.5GHz, Pin=10dBm f=1.0GHz, Pin=0dBm f=2.0GHz, Pin=0dBm f=1.0GHz, Pin=0dBm f=2.0GHz, Pin=0dBm f=2.0GHz f=0.05~2.5GHz, ON STATE f=0.05~2.5GHz MIN -0.2 2.5 25 23 19.0 - TYP 0 2.7 1.0 0.3 0.5 28 27 22.0 1.2 15 MAX 0.2 5.5 2.0 0.6 0.8 1.5 - UNITS V V uA dB dB dB dB dBm Isolation 2 (PC-P1, PC-P2, P1-P2) Pin at 1dB compression point VSWR Switching time ns -2- NJG1506R sTYPICAL CHARACTERISTICS -3- NJG1506R sTYPICAL CHARACTERISTICS -4- NJG1506R sTYPICAL CHARACTERISTICS -5- NJG1506R sTYPICAL CHARACTERISTICS -6- NJG1506R sTYPICAL CHARACTERISTICS -7- NJG1506R sTYPICAL CHARACTERISTICS MARKER 1 2 3 4 5 f (MHz) 50 800 1500 2000 3000 Mag. 0.957 0.782 0.759 0.747 0.710 Ang. (o) -20.2 171.2 102.0 61.8 -11.3 MARKER f (MHz) 1 2 3 4 5 50 800 1500 2000 3000 Mag. 0.968 0.782 0.749 0.734 0.690 Ang. (o) -20.2 174.5 108.2 69.5 -1.2 -8- NJG1506R sTYPICAL CHARACTERISTICS Scattering Parameters: S11 (OFF STATE) (VCTR=0/2.7V, 50System) -9- NJG1506R sAPPLICATION CIRCUIT 1: Single control signal operation by using C-MOS inverter. 510k [1] Please connect bypass capacitors to the supply terminals of the C-MOS inverter. [2] In order to stabilize input impedance of inverter, please pull down using 510k resister from the input terminal of the C-MOS inverter to the ground. sAPPLICATION CIRCUIT 2: Single control signal operation by using a transistor. 47k 270k 100k - 10 - NJG1506R sTEST CIRCUIT sRECOMMENDED PCB DESIGN (TOP VIEW) PC PCB SIZE=19.5x14.0mm PCB: FR-4, t=0.2mm CAPACITOR: size 1005 x C1 STRIPLINE WIDTH=0.5mm C3 C1~C3: 56pF P2 P1 C2 NJG1506R 1 C4 C5 C4, C5: 10pF x: Please short between Pin4 and ground plane directly as close as possible. V CTR1 V CTR2 Precautions [1] External capacitors should be connected to the input and output RF terminals (P1, P2, PC) to block the DC current. The above example is a circuit at 900MHz. Please select the capacitor value suitable for actual frequency from 10pF to 1000pF. [2] Decoupling capacitors should be connected to the control terminals (VCTR1, VCTR2) as close as possible. The values of these capacitors should be selected from 5pF to 100pF range. Please consider that these values are very effective to switching time (Larger capacitor gives longer switching time). [3] In order to keep good isolation characteristics, the ground terminals (3, 4, 6pin) should be connected to the ground pattern with wider width as close as possible, and through-hole in the ground plane should also be placed as close as possible. - 11 - NJG1506R sPACKAGE OUTLINE (VSP8) Lead material Lead surface finish Molding material UNIT Weight : Copper : Solder plating : Epoxy resin : mm : 22mg Cautions on using this product This product contains Gallium-Arsenide (GaAs) which is a harmful material. * Do NOT eat or put into mouth. * Do NOT dispose in fire or break up this product. * Do NOT chemically make gas or powder with this product. * To waste this product, please obey the relating law of your country. This product may be damaged with electric static discharge (ESD) or spike voltage. Please handle with care to avoid these damages. [CAUTION] The specifications on this databook are only given for information , without any guarantee as regards either mistakes or omissions. The application circuits in this databook are described only to show representative usages of the product and not intended for the guarantee or permission of any right including - 12 - |
Price & Availability of NJG1506R
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |